Magic Chef Error Code F1
Since I was digging around I reread the model number. If the F1 does not come back then the touch pad has a shorted switch. by LYLE W. Unfortunately, the keypad is part of the front panel, so it will cost me about $150.00 to replace it. have a peek here
My oven is hard wired into a junction box so your suggestion would require me to pull the oven out and rewire. Other than the F1 error, we don't seem to have any other issues. If the oven temperature sensor probe measures approximately 1100 ohms then the oven control/clock assembly will need to be replaced. STAND MIXERKitchenAid9KSM95AC04 1/2 QT.
Magic Chef Stove F1 Alarm
Can't thank you enough! STAND MIXER - JAPANWhirlpool9KSM150PSGR05 QT. I will have to check it. #7 (permalink) 03-20-2009, 12:30 PM denman Senior Expert APP Volunteer Join Date: Feb 2008 Posts: 19,612 Starting to sound like the control I have taken the time to research your question and noticed that someone else had asked a similar question with a response from an expert.
Disconnect power to stove 2. I have 2 questions: Question 1) Does the troubleshooting scenero below look correct? Great video and the technician explained everything. Magic Chef Error Codes Gas Range w/ ...
I recommend that you check around the opening to the oven cavity for a model number plate. Magic Chef F1 Test Password Show Threads Show Posts Register | FAQ's | New Posts | Today's Posts | Extras Go to Page... Appliance Repair Forum > Appliance Repair Help > Oven NOTE: Before scheduling service, I recommend that you check on the availability of parts if that Magic Chef oven is older that 10 years. ft.
Some of the touch pads are available separately even though they may not be listed as a separate part on the parts breakdown. Magic Chef Oven Beeping F7 Refer to F1 Test for more information. Thanks for all of the videos Dan McComb Very well explained and demonstrated! By reading any content on this site you agree to AppliancePartsPros.com , Inc.
Magic Chef F1 Test
Re: Magic Chef Electric Oven F1 Code Scott H. -- Sunday, 23 December 2001, at 3:47 p.m. http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/25210-magic-chef-f1-error.html How do I get access to the back of the [electronic control]? Magic Chef Stove F1 Alarm www.Appliance411.com The Appliance Information Site =D~~~~~~ Reply With Quote 05-11-2006,10:17 PM #3 wak Handyman Join Date Feb 2006 Posts 33 Thanks 0 Thanked 0 Times in 0 Posts wow, $222 for Magic Chef Control Board And since it so easily done, I can send one of the kids downstairs to hit the remote button!
See Details Kenmore 73032 4.2 cu. navigate here I disconnected the ribbon cable from the keypad/front panel and so far I have not gotten the error code. Testimonials My technicians use your videos, and it has helped out tremendously when they are stuck on a call. Tom Hoehler Thx for another great video. Magic Chef F3 Error Code
I have to keep the : circuit breaker off when I am not using it. : Anybody know what causes this? Is that in the back of the stove? ryk1265 We pass out the website on every over the counter sale! Check This Out If you get the F1 and beep, replace the ERC. 8.
They are very helpful to me thanks for taking the time to help beginners like me. Magic Chef Oven Error Code F5 I 10/19/2016 10/19/2016 smitty1486 X Ask an Appliance Technician Get a Professional Answer. 100% Satisfaction Guaranteed. 23 Appliance Technicians are Online Now Type Your Appliance Question Here... See Details Whirlpool WFG320M0BW 5.1 cu.
This doesn't : come apart, does it?
The error message hasn't return since but I'll keep my fingers crossed. F1 Defective touch pad or clock (ERC) Replace touch pad or clock (ERC). That is just a guess through. Magic Chef Oven Temperature Sensor STAND MIXER - JAPANWhirlpool9KSM150PSPK05 QT.
There are a lot of fasteners, none of which look like they give acess to the LED reading control panel. Should the sensor proves good, then the problem is most likely the membrane switch. Your directions were easy to follow. http://threadspodcast.com/magic-chef/magic-chef-oven-error-code-f3.html I ended up turning the power and gas off to it.
I don't think pulling that cable too often is a good idea as it's eventually going to cause a problem with the cable itself. Submitted: 5 years ago. Also check the ribbon cable for hairline cracks across the tracks a magnifying glass hep here. Dan O.