Home > Machine Error > Machine Error 78 Brother

Machine Error 78 Brother

Well, if you run into a overheat issue if you turn the machine back on right after, it starts to heat up again which could result in melting the fuser pressure All other I've had to actually go into  maintenance mode and clear the 76, 77, 78 Fuser / machine error through the exit and restart  sequence.Majority of the time, the 76, What to do: Machine Error: 41 Error Code: Printhead Error: The machine has detected a problem with the functioning of the printhead. If the error persists then an engineer will be required to determine the cause if it. Source

clean reset receiving fuser print sleep Drum toner replace drum reprint error confirmation... AppleTalk Troubleshootingpage 237................................................................................................................................................................ I tried carefully blowing out the fuser with a compressed air nozzle, but this did not clear the fault. Please use the previous link instead. http://www.fixyourownprinter.com/posts/29075

The machine has detected a problem with this unit. This is collected in a waste ink tank and this has become full. What to do: Machine Error: 41 Error Code: Printhead Error: The machine has detected a problem with the functioning of the printhead. Question about Brother Fax Machines 1 Answer Will not receive fax ...error 76 or 78 you will need to have service done on your machine to have either the lamp or

Problems receiving faxes Follow the steps listed below to resolve the issue. If the error persists then the laser will need replacing. The top half then slides back and up away from the machine. Explanation: Remove paper tray and look for jammed paper.

Explanation: Worn rollers can cause paper feed problems and jams.The MP tray roller kit will need replacing and the life counter resetting. What to do: Machine Error: 50, 51, 52 Error Code: Purge Unit Error: The purge unit is used to clean and prime the printhead. Open the body of the printer and check for jammed paper. directory If you still get another error in the 70's then perform a 91 intialise and that should do it.Good luck.

What to do: Error Code: 57 Error Code: Paper Jam in Duplex: A paper jam has occurred in the unit that turns the page for double sided printing. I tried carefully blowing out the fuser with a compressed air nozzle, but this did not clear the fault. The machine apparently goes into the maintenance mode at first (as evidenced by the Fine, S.Fine, and toner symbols flashing), but the display still reads MACHINE ERROR 78/OFFLINE. Brother says (after 45 minutes on hold) this part is not replacable and in machine error mode intentionally bricks the unit so that the entire unit is disabled.How can I by

Sign up here Find a Professional Type of Job Type of Job Additions and Remodels Appraisers and Home Inspectors Architects Bathroom Remodeling Cabinets and Countertops Carpentry Carpet Cleaning Concrete and Masonry http://www.doityourself.com/forum/computers-internet-capable-devices-peripherals/212906-machine-error-78-printer.html Ask Anonymously Popular Products Brother IntelliFax-2820 Laser Fax 2 Questions Brother IntelliFAX 4100 Laser Fax 1 Questions Brother IntelliFAX 1270E Plain Paper Fax 1 Questions Brother IntelliFAX 775 Plain Paper Thermal by unknown on May 27, 2010 at 8:17am Add comment Please sign in to comment 0 Machine error 76-78 are fuser errors. 95\% of the time due to a sudden power What to do: Machine Error: A2 Error Code: Document Jam: The machine has detected a problem with a page being sent via the document feeder, possibly taking too long to scan.

Tried a different brand or type of paper? this contact form Question about Brother Fax Machines 1 Answer Machine error 78 error 78 brother fax machine gives a error 78 and the red light flashes. Explanation: Switch the machine off for 5 minutes and then back on again. You know when the lights flicker and your like what just happened.

Explanation: Switch the machine off and back on again. Explanation: Worn fuser units can cause poor quality print paper jams. Explanation: Check that the document is set correctly on the feeder, and that it is not skidding. have a peek here If the error persists then the fuser will need replacing.

Toner empty. After entering 99 to leave the maintenance mode, I get PLEASE WAIT. Explanation: Check the document is not too long and that it is not skidding or being blocked.

A problem has been with the timing of the main motor drive.

If it is not then the paper sensor may be faulty. To resolve this issue, you will need to uninstall the existing... VIDEO is displayed. Explanation: Remove paper tray and look for jammed paper in path.

At 8 seconds PLEASE WAIT/WARMING UP appears. Once entered the machine will beep, the lights on the display will flash and it will read MAINTENANCE. poor line... Check This Out Explanation: Replace the toner unit.

After pressing "91" in the maintenance mode, PARAMETER INIT appears for one second then the display reverts to MACHINE ERROR 76/OFFLINE.Regards,Edwin by unknown on Feb 25, 2009 at 2:05pm Add comment What to do: Error Code: 68, 69, 6A, 6B, 6C, 6D, 6E, 6F Error Code: Fuser Unit Failure: These codes all apply to the fuser unit. Explanation: Switch the fax machine off and back on again. Press MENU,*,2,8,6,4 If done correcty the machine reads "Maintenance" Next press 9,9 which should reset the code and exit out of service mode.

I should have torn-down the printer before buying a new fuser, but did not want to leave a pile of screws and parts sitting around while looking for replacement parts. The fuser isnt that costly anymore I'll look when I get a chance. step 1 step 1 choose your brother printer Choose a printer family Printer Family Just-Printers Multi-functional-Printers Fax-machines Printer Family step 2 choose your brother model step 2 Choose your Brother Model Explanation: Check the paper path is clear of obstructions.

Explanation: Worn laser units can cause poor quality print. Explanation: An engineer wil be required to replace the waste ink box and reset the waste ink counter. What to do: Error Code: 32 Error Code: Density Sensor Shutter Failure: The density sensor has a protective cover that is operated by a solenoid. I think I've only seen one machine reset itself.

Explanation: Switch the printer off and back on again. What to do: Error Code: 7D Error Code: Dirt on Drum Unit: The printer is detecting contamination in the drum unit area. This the first and only time this error has occured. What to do: Machine Error: A2 Error Code: Document Feed Error: The machine has detected a problem when transmitting a document.

I'm also having "Machine Error 76" recently, also. Or just drag it here! The main thing a can say here is not to read the screen. Firmware update Updating the firmware will delete some data from your Brother machine such as secured print data, caller ID log, journal report, outgoing message,and more (features depend on your model...

Small piece of paper stuck in the printer?