Home > Error Code > Macintosh Se Error Code

Macintosh Se Error Code


No FPU Installed is equivalent to a Type 10 Error i.e., your program has attempted to execute an unknown instruction op code starting with the hex value F. ID=03 Illegal Instruction The computer has a specific vocabulary of machine language instructions it can understand. Then click 'Open', then "Start". The current version of Hard Disk Toolkit says it requires a Power Macintosh, so it's of no use to you. Source

Keywords: kppc,supt,ksts,hts,ktoptil,kfax ====================================-------- This information is from the Apple Technical Information Library. I took a closer look at the two systems OSs, and I realized that the SE/30 is running System 7.1, not 6.1 as I believed earlier. OFOO02 Mac Plus/512Ke with HD, partition map went bad, low level format the drive with HD formatting software. 0F0003 Mac Plus/512Ke with HD, partition map went bad, low level format the So, I am restricted to sneakernet to update these computers. http://www.gla.ac.uk/~gwm1h/Error_Codes/Sad_Mac_Codes.html

Mac Sad Face On Startup

Or a single-floppy machine may have had its hard drive removed. The air flow for a Mac SE >> has part of the air coming in through the floppy slot, so dust and lint >> builds up in the drive. If it only works with 400 K, then something is keeping one of the pair of heads for top and bottom of the disk from working. You need StuffIt to decode the boot-disk file from the "MacBinary" format used to store Macintosh files on the internet.

This may indicate either a bad RAM chip or data bus failure. $0B - Unable to properly access the SCSI chip. This discussion is locked Hugh Christian Level 1 (35 points) Q: Updating OS on Mac SE I have recently acquired 2 working Macintosh SEs. Here's how. Happy Mac Any Mac can be upgraded, but it's a question of what can be upgraded - RAM, hard drive, video, CPU - and how far it can be upgraded.

If anyone has some step by step instructions on how to proceed, I would appreciate it.Thanks,hbchrist Posted on Sep 12, 2005 12:02 PM I have this question too Close Q: Updating I > have always kept an eye on it, even though I can call it mine > for only 10 years now. Online Resources Guide to Compact Macs, a quick overview of Apple's 10 compact Macs. http://www.motherboardpoint.com/threads/old-mac-se-sad-mac-error.201011/ Power Manager Communication Error Codes $CD38 Initial handshake. $CD37 No reply to initial handshake. $CD36 During send, no start of a handshake. $CD35 During a send, no finish of a handshake.

Key component is a SCSI-ethernet adapter. Mac Error Code Don't put too much pressure on the head and do not >> take apart the heads, you will a have near impossible task of realigning >> them. Helpful (0) Reply options Link to this post Page 1 Next This site contains user submitted content, comments and opinions and is for informational purposes only. But the base SE ROM should definitely support the 800K format.

Sad Mac Sound

If that works, all you have to do is replace the hard drive. As for the drive, here I now of a few sources where I can get a new or refurbished replacement floppy drive for $5-10. Mac Sad Face On Startup Probably, I will try to clean the drive. Sad Face On Mac When a system crash occurs, you'll lose less data if you've taken these precautions.

If the problems continue, particularly in the Finder, there may be an issue with your Apple or non-Apple hardware. this contact form It's less likely than error 02, but still very common. Anything with a 50-pin SCSI connector should work, although versions of MacOS compatible with an SE will limit you to 2G per disk partition - so you'll end up with a So I copied the folder from the boot floppy to the hard disk. Chimes Of Death

If you get the blinking '?' yet again, push the boot disk back in the drive slot and let the SE start up from that. This way both the exception that occurred as well as the test that was running can be decoded from the major error code: SAD MAC CODE FURTHER BROKEN DOWN 68000 Exception I had to hard boot again, and now the system does any one of the following upon reboot: - boots off the floppy, then gives me a finder error - boots have a peek here ID=08 Trace Mode Error A programmer can use a runtime debugger while in Trace mode.

If you only find one sensor that matches up with write protect hole on a floppy, then you have one of the 400/800 K drives. Apple Support For a complete list of available Fax documents, search the Tech Info Library for Apple Fax Document Index or call the Apple Fax line at 1-800-505-0171 and select document number 20000 Old Macs can exchange data and share an Internet connection very nicely using Apple's old LocalTalk networking.

However, the magnetic properties are not identical, so expect errors.It may be a good idea to reformat the hard disk on the (plain) SE via the System 7.0 Disk Tools floppy.

Minor error code indicates the bad bits as a 16bit mask for bits 1500. Mailing Lists Mailing lists Feeling really retro today? If it does, you're done. (You can delete the "Old System Folder", but take a look at what's in it first so you can keep anything that seems useful). If the procedures described below seem daunting, you could try persuading some helpful person to make and snail-mail you a System 6.0.8 floppy boot disk.

There are many Web sites on the Internet for example, Apple's Third-Party Development Products Database at lists many Macintosh development tools. See here for details. You can get them at Radio shack. Check This Out Both error messages are the result of programming errors.

Your SE has two floppy disk drives and no hard drive. Which system software is best for my vintage Mac?, Tyler Sable, Classic Restorations, 2005.11.22.